深圳艾普检验认证有限公司
全球服务热线:
+86 13480108853
全球市场准入
为您的目标国家/地区和产品量身定制解决方案!
你想拥有哪座城?
新闻中心
无线产品美国FCC认证须知
来源: | 作者:admin | 发布时间: 2021-10-12 | 1546 次浏览 | 分享到:
根据美国联邦法规相关部分(CFR 47)的规定,凡进入美国的电子产品都需要进行FCC认证(极少数有关条款特别豁免的产品除外)

关于美国FCC

FCC全称Federal Communications Commission,即美国联邦通信委员会。于1934年根据Communications Act建立,是美国政府的一个独立机构。根据美国联邦法规相关部分(CFR 47)的规定,凡进入美国的电子产品都需要进行FCC认证(极少数有关条款特别豁免的产品除外)。FCC法规的要求涵盖发射机要求、无线设备、电磁兼容要求、电话终端设备、测试方法等技术规范、行政要求以及其它的市场准入条件。产品主要分为四类:偶然发射体、无意发射体、有意发射体、需要执照的发射机。绝大部分的无线设备(蓝牙,Wi-Fi,2/3/4/5G等)都属于有意发射体。


FCC认证程序类别

1、Certification(FCC-ID证书)

发证是射频设备最严格的审批流程,基本适用于所有无线设备。由FCC认可的电信发证机构(TCB)根据责任方(如制造商或进口商)向TCB提交的证明文件和测试数据的评估而颁发的设备授权(TCB Grant)。

测试须由FCC认可的测试实验室执行。所有的证书和相关产品的符合性文件及产品文件将上传到FCC的数据库中,并部分公开给大众,如测试报告,说明书等。

此外,使用供应商合规声明 (SDoC) 程序获得批准的设备可以选择性地使用发证程序。


2、Supplier’s Declaration of Conformity - SDoC(供应商的合规声明)

供应商的合规声明 (SDoC) 是一个程序,要求负责产品符合性的责任方(Responsible Party)确保设备符合相应的技术标准。

责任方必须位于美国,无需向FCC或 TCB 提交发证申请。根据 SDoC 程序授权的设备不会列在FCC数据库中。但是,责任方或销售设备的任何其他方必须应FCC的要求提供测试报告和其他信息,证明其满足FCC要求。责任方可以选择使用发证程序来代替 SDoC 程序。

使用并满足SDoC程序要求的产品可自主选择标记或不标记 FCC logo。


FCC测试标准


无线技术/功能

人体辐射安全要求

无线射频要求

EMC电磁兼容要求

Bluetooth & Zigbee

(2.4 GHz)

Part 2

(无需测试)

Part 15C


Part 15B

Wi-Fi 2.4 GHz(802.11 b/g/n)

Part 15C

Part 2(如果正常使用贴近人体则需要测试SAR)

Part 15C


Part 15B

Wi-Fi 5 GHz(802.11 a/ac/ax/n)

Part 15B

Part 2(如果正常使用贴近人体则需要测试SAR)

Part 15E

Part 15B



文件要求

1.FCC ID标签,标签位置信息

2.产品外观图

3.原理方框图

4.线路图

5.测试报告

6.测试设置照片

7.用户手册

8.产品内部照片

9.元件清单

10.人体辐射评估

11.产品工作原理描述(使用5 GHz频段的产品需要提供额外软件安全性描述文件)

12.相关申请信、授权信、保密要求表等

取得认证后,制造商便可在产品上打上相应标签,并在说明书上加注对应FCC指引,产品即可进入市场进行销售。


FCC标识及警告语要求

产品及包装上(或说明书)都需要FCC及IC标识,要求如下:带无线发射产品:
A 发射产品上: ID XXXXXXXX.可以用贴纸或丝印等方式,
B 接收部分的标识如下(30MHz以下的接收器不用加贴--参考FCC15.101):
   Trade Name:(品名或公司名)
   Module No. (产品型号)            
   This device complies with Part 15 of the FCC Rules.
   Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference that may cause undesired operation.

C 包装或说明书(或吊卡)上的标识:

WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
 

FCC标识方法: 布标、丝印移印、贴纸(贴纸必须是过胶或胶质的,且粘贴牢固)等。


其他注意事项
不准贴在电池盖等可移除的部件上,可张贴在底座等不影响外观的位置.
包装上标识的文种与其他包装文字文种对应, 产品上则可只要英文如彩盒是英法文的,则也需要英法文.


FCC KDB技术文件的更新

KDB 447498 D01 General RF Exposure Guidance DR04是基于KDB 447498 D01 V06要求及FCC-19-126规则进行了修改和更新。以上内容将汇总并通过KDB 447498 D01 General RF Exposure Guidance V07发布。2022年3月31日后提交的所有申请都必须使用新版KDB 447498 D01 V07。

KDB388624 D02 PAG(预审批) 列表v17r03替换KDB388624 D02 PAG(预审批)列表v17r02,将UN5GHZ添加到PAG列表中。


如您有相关认证需求,欢迎随时联系我们。